British and European Car Spotters Guide - 1948

Send This Page To A Friend

During 1948 many new models were introduced to the UK market. These were the real post-war designs with new modern full-width bodywork and usually with such features as independent front suspension, steering column gear change, bench-type front seats, etc. Most of them were not available for the domestic market where buyers had to be content with earlier models. These, however, were gradually phased out of production because manufacturers needed all their production capacity for the new models, and owing to a drastic change in the road tax system (a flat rate, rather than based on the old hypothetical RAC formula) there was no longer such a need for the old-fashioned small-bore Eights and Tens.

Rationalization and concentration on a minimum number of different models were of paramount importance. Some 330,000 cars were produced, more than two-thirds of which were exported. UK registrations numbered 112,666 new cars and just over 10,000 'hackneys'. 221 cars were imported. New car prices, where quoted, were valid in May 1945, and include purchase tax, unless stated otherwise. One of the biggest events of 1948 was the first post-war London Motor Show at Earls Court, in October/November. It was the first since 1939, and most manufacturers displayed their new models, the majority of which are considered 1949 models.
1948 AC 2 Litre Saloon Shooting Brake
UK

AC 2 liter Saloon "Shooting Brake"

  Also see: AC Car Reviews | The History of AC (AUS Edition)
 
AC continued their 2-liter model. mainly in two-door Saloon form. Pictured left is a rare and rather ungainly 'shooting brake', built on the same chassis. Similar bodies appeared on other high-grade chassis, including Alvis and Riley When equipped with rear doors and folding rear seat, like this example, they were classed as Utility Cars.
1948 Alvis Fourteen Model TA14 Drophead Coupe
UK

Alvis Fourteen Model TA14 Drophead Coupe

  Also see: Alvis Car Reviews | The History of Alvis
 
The Alvis Fourteen Model TA14 Drophead Coupe was introduced in January 1948, and offered until September of the following year. The bodywork was by Carbodies Ltd, whose plant was opposite Alvis' own, in Coventry's Holyhead Road. The chassis price was £665 (basic), while the complete car cost £1276, which was the same price as for the Saloon.
1948 Alfa Romeo 6C 2500 Gran Turismo
Italy

Alfa Romeo 6C 2500 Gran Turismo

  Also see: Alfa Romeo Car Reviews | The History of Alfa Romeo
 
Introduced in 1938, the 2500 (2443 cc) was the last 6C road car. World War II was coming and car development was stopped, but a few hundred 6C 2500s were built from 1940-1945. Postwar, the first new Alfa model was the 1946 6C 2500 Freccia d'Oro (Golden Arrow), of which 680 were built through 1951, with bodies by Alfa. It was sold to wealthy customers like King Farouk, Alì Khan, Rita Hayworth, Tyrone Power, and Prince Rainier. The 6C 2500 Villa d'Este was introduced in 1948 and was produced until 1952, named for the Concorso d'Eleganza held in Villa d'Este; a Touring Superleggera-bodied version won the prize. Villa d'Este was Alfa's last hand built model, only 36 examples made. The last 6C was produced in 1952, and was replaced by the 1900.
1948 Armstrong Siddeley Hurricane Drophead Coupe
UK

Armstrong Siddeley Typhoon 2 door, Lancaster 4 door Saloon and Hurricane Drophead Coupe

  Also see: The History of Armstrong Siddeley
 
Armstrong Siddeley continued their 1947 Sixteen 2-liter programme, comprising the Typhoon two-door and Lancaster four-door Saloons and the Hurricane Drophead Coupe. The Drop Head Coupe cost £1247. The Typhoon, which was also known as Sportsman's Saloon, carried the same price tag. All three were superseded, in September 1949, by 2309cc engined models.
1948 Aston Martin DB and DB Spa Replica
UK

Aston Martin DB and DB Spa Replica

  Also see: Aston Martin Car Reviews | The History of Aston Martin
 
Aston Martin and Lagonda were taken over in 1947 by David Brown (later Sir David). At this time the tubular chassis and a new 1970-cc OHV engine were still under development. Shown is the first DB Aston Martin, the car that won the Spa 24-hour race in 1948. The picture shows the car as it was at the 1948 London Motor Show, with revised bodywork. A similar car, called the Spa Replica, was marketed during 1948/49 at £3110.
1948 Aston Martin 2-Litre Sports
UK

Aston Martin 2-liter Sports

  Also see: Aston Martin Car Reviews | The History of Aston Martin
 
Aston Martin 2-liter Sports 2-4-seater was the first post-war Aston Martin to be offered to the public, at £2332 (October 1948). The prototype had run as a practice car at Spa. The 1970-cc (82·55 x 92 mm) four-cylinder pushrod OHV engine had a CR of 7·25:1 and twin SU carburetors. The maximum power output was 90 bhp at 4750 rpm (95 bhp on the Spa Replica model). Both cars had a four-speed gearbox and 9 ft wheelbase. The Sports (later known as DB1) had 5.75-16 tires, the Spa Replica 5·25-18, both on wire spoke wheels. They were produced at Feltham in Middlesex.
1948 Austin Sixteen Model BS1 Saloon and BW1 Countryman
UK

Austin Sixteen Model BS1 Saloon and BW1 Countryman

  Also see: Austin Car Reviews | The History of Austin (AUS Edition)
 
Austin 1946/47 models were disconntinued with the exception of the Sixteen Model BS1 Saloon and BW1 Countryman.
1948 Austin A135 Princess
UK

Austin A135 Princess

  Also see: Austin Car Reviews | The History of Austin (AUS Edition)
 
The Austin A135 Princess, Model DS2. was mechanically similar to the A125 Sheerline, Model DS1, except for triple SU carburetors (v. single Stromberg) and higher final drive ratio. The main difference was that the £1277 Sheerline was entirely Austin-built. whereas the Austin A135 Princess had coachwork by Vanden PIas. Both had a 4-liter OHV Six engine and coil-spring independent front suspension. Successors to a long line of Austin Twenties, the A125 and A135 were continued for many years in various forms, including limousines and ambulances. Prices started at £2103.
1948 Austin A40 2-door Dorset G2S2 and 4-door Devon Model GS2
UK

Austin A40 2-door Dorset G2S2 and 4-door Devon Model GS2

  Also see: Austin Car Reviews | The History of Austin (AUS Edition)
 
Austin A40 two-door Dorset Model G2S2 and four-door Devon Model GS2 Saloons superseded the earlier Eight, Ten and Twelve in October 1947, at £403 and £416 respectively. The Dorset was phased out during 1948. They had a 1200-cc (65·48 x 89 mm) 40-bhp (10·7 HP) OHV Four engine with four-speed gearbox, independent front suspension with coil springs and Girling hydro-mechanical brakes. Wheelbase was 7 ft 8; in and tire size 500-16. In March 1948. a 10-cwt Van (GV2) derivative was added, followed by Countryman (GP2) and Pick-up (GQU2) modifications thereof in September.
1948 Austin A40 Devon
UK

Austin A40 Devon

 

Also see: Austin Car Reviews | The History of Austin (AUS Edition)

 
Austin A40s were sold in considerable numbers all around the world. The first A40 Devon in New York is shown here looking rather forlorn in Fifth Avenue traffic. When eventually discontinued in early 1952, over 344,000 A40s had been produced; 77% of these had been exported, earning £88 million in foreign currency.
1948 Austin A40 Hampshire
UK

Austin A40 Hampshire

 

Also see: Austin Car Reviews | The History of Austin (AUS Edition)

 
In February 1950. it was announced that the A40 had been identified as the individual British product that had earned more dollars for Britain than any other one-make commodity. namely $70 million in 160 weeks.
1948 Bond Minicar
UK

Bond Minicar

 

Also see: Bond Car Reviews | The History of Bond (AUS Edition)

 
Bond Aircraft and Engineering Co (Blackpool) Ltd of Longridge, Lancashire, introduced their first three-wheeler in mid-1948. Intended as a 'runabout for shopping and calls within a 20-30 mile radius', the car had a chassisless body of stressed-skin construction. It was powered by a 125cc Villiers two-stroke engine, mounted on a swivelling fork which carried the front wheel, suspension being by means of a trailing link. The brakes operated only on the unsprung but resiliently and independently mounted rear wheels. Shown is a prototype. Quantity production commenced in 1949 with the Mark A.
1948 Bristol 400
UK

Bristol 400

 

Also see: Bristol Car Reviews | The History of Bristol (AUS Edition)

 
The Bristol 400 2-liter underwent several changes such as a larger boot and external spare wheel mounting with fitted cover and. as can be seen here, conventional bumpers instead of the tubular type.
1948 Citroen 2CV
France

Citroen 2CV

  Also see: Citroen Car Reviews | The History of Citroen (AUS Edition)
 
Designed to carry a basket of eggs across a ploughed field without breaking one of them, the 2CV charmed Gallic peasants and Francophiles alike.
No Image
France

Citroen Light Fifteen Model PVS

 

Also see: Citroen Car Reviews | The History of Citroen (AUS Edition)

 
By 1948, Citroen Cars Ltd (UK) had been assemblers of Citroen front-wheel drive cars for many years, importing the body pressings and mechanical components from France. Many British-made components and fittings were utilized. The Light Fifteen Model PVS was in production for exactly ten years, from October 1945, and in October 1948 was joined by the Series 15C Six which was similar but larger (wb 10ft 1½ in v. 9 ft 6½ in. 2866-cc six-cylinder engine v. 1911cc Four. etc.).
1948 Commer Superpoise
UK

Commer Superpoise

 

 

 
The Commer Superpoise passenger-utility vehicle was based on light truck chassis. It was supplied to Vickers-Armstrongs Ltd, Superrmarine Works. It was powered by what was basically the same 1944-cc four-cylinder engine as that used in the contemporary Humber Hawk, both makes being members of the Rootes Group.
1948 Daimler 2½-Litre DB18 Saloon and Drophead Coupe
UK

Daimler 2½-liter DB18 Saloon and Drophead Coupe

 

Also see: Daimler Car Reviews | The History of Daimler (AUS Edition)

 
Daimler continued their 2½-liter DB18 in Saloon and Drophead Coupe form. The chassis was available at a basic price of £1065 for bodywork by other coachbuilders and shown here is a Drophead Coupe by Tickford Ltd of Newport Pagnell, Bucks.
Fiat Topolino
Italy

Fiat Topolino

  Also see: Fiat Car Reviews | The History of Fiat
 
The Topolino was one of the smallest cars in the world at the time of its production. Launched in 1937, three models were produced until 1955, all with only minor mechanical and cosmetic changes. It was equipped with a 569cc four-cylinder, side valve, water-cooled engine mounted in front of the front axle, and so was a full-scale car rather than a cyclecar. The radiator was located behind the engine which made possible a lowered wind-cheating nose profile at a time when competitor vehicles confronted the world with flat near vertical front grills. The shape of the car's front gave it exceptional forward visibility.
Fiat Topolino
Italy

Fiat Topolino

  Also see: Fiat Car Reviews
 
The Topolino's rear suspension initially depended on quarter-elliptic rear springs, but somehow buyers frequently squeezed four or five people into the nominally two seater car, and in later models the chassis was extended at the rear to allow for more robust semi-elliptic springs. With horsepower of about 13 bhp, its top speed was about 53 mph (85 km/h), and it could achieve about 39.2 miles per US gallon (6.00 L/100 km; 47.1 mpg-imp).
Fiat Topolino
Italy

Fiat Topolino

  Also see: Fiat Car Reviews
 
The target price of the Topolino was 5,000 lire, but the price at launch was 9,750 lire, though the decade was one of falling prices in several parts of Europe and later in the 1930s the Topolino was sold for about 8,900 lire. Despite being more expensive than first envisaged, the car was very competitively priced. Nearly 520,000 were sold. In 1955 the mid-size rear wheel drive Fiat 600 was launched by Fiat and that would become the design basis for the new Fiat 500, the Nuova 500. The Nuova 500 is often thought, mistakenly, to be the only model 500 Fiat.
1948 Fiat Topolino
Italy

Fiat Topolino

  Also see: Fiat Car Reviews
   
1948 Ford Pilot Saloon Model E71 A
UK

Ford Pilot Saloon Model E71 A

 

Also see: Ford UK Car Reviews | The History of Ford

 
The Ford Pilot Saloon, Model E71 A, was introduced in August 1947, and continued until 1951. Except for the front end, the four-door four-light bodywork was very similar to that of the pre-war 22 HP Model 62. When the Pilot was introduced there was to be a choice of 2·5 and 3·6-liter V8 engines, but it was soon decided to fit only the larger unit (basically identical to that of the contemporary Fordson Thames trucks). This 3622-cc (77·8 x 95·3 mm) unit produced 85 bhp at 3500 rpm and drove through a three-speed gearbox with steering-column mounted shift lever. Suspension was in the Ford tradition with rigid axles and transverse leaf springs. Available for export was an 'equipped chassis' (Model E71 C) for pick-up truck bodies. Some export models had vertical louvres in the bonnet side panels. A metal Estate Car variant was offered, but supplied almost exclusively to Government departments.
1948
UK

Ford Anglia and Prefect

 

Also see: Ford UK Car Reviews | The History of Ford

 
The Ford Anglia and Prefect were continued with little change except that in December 1947, the word 'Anglia' had been incorporated in the radiator grille badge and the Prefect had chrome radiator slats and plain hub caps from October 1947.
1948 Hillman Minx
UK

Hillman Minx

 

Also see: Hillman Car Reviews | The History of Hillman (AUS Edition)

 
The Hillman Minx for 1948 was announced in December 1947, and known as the Mark II, was facelifted and modified in several respects. Bonnet, bumpers. front wings and dashboard were restyled and the four-speed gearbox had steering-column gearshift. The radiator grille was no longer integral with the bonnet and the headlamps were built-in. The wheels were now of the full-disc type. Another important modiification was the change from mechanical to hydraulic brakes. The Saloon was priced at £493.
1948 Hillman Minx Mark II Drophead Coupe
UK

Hillman Minx Mark II Drophead Coupe

 

Also see: Hillman Car Reviews | The History of Hillman (AUS Edition)

 
The Hillman Minx Mark II Drophead Coupe featured the same improvements and modifications as the Mark 11 Saloon plus the omission of the 'hood irons' of the convertible top. The Mark II Minxes were not produced for very long. After nine months they were superseded by the entirely restyled Mark III models.
1948 Hillman Minx Mark II Estate
UK

Hillman Minx Mark II Estate

 

Also see: Hillman Car Reviews | The History of Hillman (AUS Edition)

 
Hillman Minx Mark II Estate Car shared its rear body styling with the Minx-derived Commer light van.
1948 HRG 1100 and 1500 sports
UK

HRG 1100 and 1500 Sports

 

 

 
HRG 1100 and 1500 sports two-seaters with their characteristic quarter-elliptic leaf-sprung tubular front axle were continued from 1947 but production of the 90-mph Aerodynamic model was dropped. The 1100 and 1500 were continued until the mid-1950s when all HRG production ceased.
1948 Humber Hawk Interior
UK

Humber Hawk, Snipe and Super Snipe

 

Also see: Humber Car Reviews | The History of Humber

 
The Humber Hawk, Snipe and Super Snipe were continued from 1947 with very little change except the adoption of steering-column gearshift on the Hawk, in September 1947. The system was called 'Synchromatic finger-tip gear change'. With this modification the Hawk was now known as Mark II but all three cars were discontinued in September/October and superseded in production by the entirely newly-styled Hawk Mark III and face-lifted Super Snipe Mark II.
1948 Humber Hawk, Snipe and Super Snipe
UK

Humber Hawk, Snipe and Super Snipe

 

Also see: Humber Car Reviews | The History of Humber

 
The Humber Pullman was the first Humber to receive a post-war face-lift clearly from the same Rootes stylists responsible for the Hillman Minx Mark II. The Pullman in its basic form was a Limousine and the new edition, again bodied by Thrupp & Maberley, was designated Mark II. Pictured left are two special-bodied Pullmans, produced for the Royal Tour of Australia and New Zealand. Humber, in conjunction with the Governments concerned, provided three Landaulettes (right) and two Touring Cabriolets (left) for Australia, and two Landaulettes for New Zealand. In addition ten standard Pullman Limousines and nine Super Snipes were supplied for the two Tours.
1948 Invicta Black Prince Byfleet Drophead Coupe
UK

Invicta Black Prince Byfleet Drophead Coupe

 

Also see: The History of Invicta

 
The Invicta Black Prince Byfleet Drophead Coupe was produced in 1948 and was priced at £3890. It superseded the Wentworth Saloon which was still available to special order, but which was produced mainly in 1947. Both were made only in small numbers and had many unconventional design features such as a Brockhouse Turbo Torque Converter transmission giving infinitely variable gear ratios (plus epiicyclic reversing gear), X-form frame with torsion bar independent springging front and rear, inboard rear brakes, etc. The 2998-cc 120-bhp six-cylinder engine embodied a 24-volt dynamotor, coupled direct to the front end of the crankshaft. The power unit was based on a Meadows industrial engine and had twin overhead camshafts, non-adjustable valves and three SU carburetors. The coachwork was made by Jensen of West Bromwich.
1948 Jaguar 1.5, 2.5 and 3.5 Litre Saloon
UK

Jaguar 1½, 2½ and 3½ liter Saloon

 

Also see: Jaguar Car Reviews | Jaguar - A Racing Pedigree

 
Jaguar 1½, 2½ and 3½ liter Saloon models were continued from 1947 and in October were joined by revised 3½ liter Mark V models. Mid-1948 prices were: 1½- liter £953 (special equipment model (1009), 2½-liter £1189, 3½-liter £1263.
1948 Jowett Javelin Drophead Coupe
UK

Jowett Javelin Drophead Coupe

 

Also see: Jowett Car Reviews | The History of Jowett

 
Jowett continued their successful Javelin and 'owing to popular demand from overseas' introduced a Drophead Coupe variant: a five-seater with a three-abreast bench seat plus a separate two-seat 'dickey' in the rear (outside). It was displayed at the 1948 Earls Court Motor Show. The tail end of necessity being unusually long, this car looked very ill-proportioned and, not surprisingly, was not produced in quantity.
1948 Lagonda 2.5 Litre Saloon and Drophead Coupe
UK

Lagonda 2½-liter Saloon and Drophead Coupe

 

Also see: The History of Lagonda

 
Lagonda 2½-liter Saloon and Drophead Coupe were produced in very small quantity in 1946/47, after which the company was bought by Mr David Brown who resumed production by the autumn of 1948. The 2580cc (78 x 90 mm) engine had twin overhead camshafts and twin SU carburetors. It developed 105 bhp at 5000 rpm. Wheelbase was 9 ft 5½ in. Suspension was independent with coil springs at front and torsion bars at rear. Prices in August 1948: Saloon £3110, Drophead Coupe £3421.
1948 Land Rover Series 1
UK

Land Rover Series 1

  Also see: Land Rover Car Reviews | The History of Rover (AUS Edition)
 
Rover's new four-wheel drive utility vehicle, very appropriately called Land-Rover (one of the cleverest features of the vehicle!), went into quantity production in July 1948, after having made its world debut at the Amsterdam Motor Show in April. The first Land- Rovers had the same engine as the Rover Sixty car. It was intended as a stop-gap to keep Rover busy in post-war years, the Series I workhorse had aluminum bodywork because of steel rationing. It's now an icon that has explored every continent on earth.
1948 Lea Francis 14 HP Sports Two-seater
UK

Lea Francis 14 HP Sports Two-seater

 

Also see: The History of Lea-Francis

 
Lea-Francis Cars Ltd of Coventry, in addition to their Fourteen Saloon, Coupe and Utility models, offered this 14 HP 1767-cc Sports Two-seater on 8 ft 3 in wheelbase chassis. On the home market it was priced at £1276. It was also available with a 12 HP 1496-cc engine at the same price.
1948 MG Midget TC
UK

MG Midget TC

 

Also see: MG Car Reviews | The MG Story | The History of MG

 
The MG Midget TC was a carryover from 1947 and continued to sell well, especially in North America. It was particularly popular in California, where it created much goodwill for British sports cars. The car had a top speed of 75 mph and was used on both street and track. In Britain the price was £528 throughout its production span.
1948 MG 1.25 Litre Saloon Model YA
UK

MG 1¼ liter Saloon Model YA

 

Also see: MG Car Reviews | The MG Story | The History of MG

 
MG 1¼ liter Saloon, designated Model YA, continued to sell at £672. Including its slightly modified successor (the 1951-53 YB) and the YT Tourer version, which had twin carburetors (1948-50), an overall total of about 8700 were produced.
No Image
UK

Morgan Three-Wheeler

 

Also see: Morgan Car Reviews | The History of Morgan

 
Morgan Three-Wheelers lined up at a British rally attracting all kinds of veteran, vintage and other special-interest vehicles in the early 1970s, Right to left: 1948, 1935 and 1949 Morgans. Four-wheeled models for 1948 were continued from 1947.
1948 Morris Six
UK

Morris Six MS Saloon

 

Also see: Morris Car Reviews | Morris Production Details 1939 - 1950

 
The Morris Six was the company's first post war six cylinder car. At launch the car was priced at £671 on the UK market. The car was very similar to the 1948 Issigonis designed Morris Oxford series MO sharing the same bodyshell from the windscreen backwards. The bonnet was lengthened to take the overhead camshaft, single SU carburetor, 2215 cc six cylinder engine which produced 70 bhp (52 kW) at 4800 rpm. The whole car was longer than the Oxford with a wheelbase of 110 inches (2,800 mm) against 97 inches (2,500 mm). Suspension was independent at the front using torsion bars and at the rear there was a conventional live axle and semi elliptic springs. The steering was not by the rack and pinion fitted to the Oxford but used a lower geared Bishop Cam system. The 10 inches (250 mm) drum brakes were hydraulically operated using a Lockheed system. The design was shared with Nuffield Organisation stable-mate Wolseley as the 6/80.
1948 Morris Six MS Saloon
UK

Morris Six MS Saloon

 

Also see: Morris Car Reviews | Morris Production Details 1939 - 1950

 
The Morris Six series MS Sedan, manufactured from 1948 to 1954. It was powered by a 2215cc six cylinder engine.
1948 Morris Eight Series E four-door Saloon in Ghost View
UK

Morris Eight Series E four-door Saloon shown in 'Ghost View'

 

Also see: Morris Car Reviews | Morris Production Details 1939 - 1950

 
Morris Eight Series E four-door Saloon 'Ghost View'. This car was in production from 1939 until November 1948. During its last year it had a spring-type steering wheel. In addition to the two and four-door car models there was a 5-cwt Van variant, Series Z, which was continued until May 1953.
1948 Morris Ten Series M
UK

Morris Ten Series M

 

Also see: Morris Car Reviews | Morris Production Details 1939 - 1950

 
Morris Ten, Series M, was a carryover from previous years and was replaced in October 1948, by the all-new Morris Oxford, Series MO.
Morris Minor
UK

Morris Minor

  Also see: Morris Car Reviews and The History of Morris (AUS Edition)
 
A national treasure in the UK, and with independent front suspension and monocoque construction, it was quite innovative when launched in 1948. Some 1.6 million were sold and the Moggie remains a popular classic.
No Image
France

Renault Eight Model BFK4

 

Also see: Renault Car Reviews | The History of Renault

 
The Renault Eight Model BFK4, as shown here. was assembled during 1947-50 by Renault Ltd of Western Avenue, Acton, London W3, largely from components imported from France and mainly for export. Although this 1948 advertisement claims that it was a genuine post-war car, it was in fact a continuation of the pre-war Juvaquatre (Eight in the UK), but with four doors and hydraulic brakes. As in 1939. the engine was a 1003cc (58 x 95 mm) side-valve Four, driving through a three-speed gearbox. Front suspension was independent with a transversal leaf spring, wheelbase was 7 ft 8½ in. tire size 4.75-16. In 1949/50 it was superseded by the rear-engined Renault 4CV (750), although the van variant (AHG2) was continued in France until 1953.
1948 Riley 1.5 and 2.5 Litre RMA and RMB Saloons
UK

Riley 1½ and 2½ liter RMA and RMB Saloons

 

Also see: Riley Car Reviews | The History of Riley

 
Riley 1½ and 2½ liter RMA and RMB Saloons were continued from 1947 with only minor technical changes. The 2½ liter, for example, was fitted with larger inlet valves from April and two leading shoe front brakes from June. From July interior bonnet locks were fitted. Price was £1125 (£863 for the 1½ liter).
No Image
UK

Riley RMC Roadster

 

Also see: Riley Car Reviews | The History of Riley

 
Riley introduced this three-seater RMC Roadster in March 1948, on the 9 ft 11 in wheelbase 2½ liter chassis. It was originally made only for export, like the Drophead Coupe variant which appeared in September 1948. In September of 1949 these two models were made available for the local UK market. The Roadster was produced until December 1950, after it had been changed to a two-seater in January of that year.
1948 RolIs-Royce Silver Wraith 4.5 Litre
UK

RolIs-Royce Silver Wraith 4¼ liter

 

Also see: Rolls-Royce Car Reviews | The History of Rolls-Royce

 
RolIs-Royce Silver Wraith 4¼ liter chassis, with Sedanca DeVille coachwork by H. J Mulliner & Co. Ltd. This was one of several body styles available. The price of the complete car was £6029.
1948 Rover P3 Sixty and Seventy-Five
UK

Rover P3 Sixty and Seventy-Five

 

Also see: Rover Car Reviews | The History of Rover (AUS Edition)

 
Rover, in February 1948, replaced their previous range of 10,12,14 and 16 HP cars by two new models, designated the P3 Series. There were two basic models, the Sixty with four-cylinder and the Seventy-Five with six-cylinder engine. The two cars shared the same 9 ft 2½ in wheelbase chassis, with minor differences to front suspension and gearbox. The difference in engine length was made up by an elongated bell-housing in the case of the shorter Sixty engine.
No Image
UK

Rover P3 Sixty and Seventy-Five

 

Also see: Rover Car Reviews | The History of Rover (AUS Edition)

 
Rover P3 Series models, both in four-cylinder Sixty and six-cylinder Seventy-Five form, were available with either four or six-light four-door body styles, without price difference, i.e. both Sixties sold at £1080, both Seventy-Fives at £1106. Compared with the previous Rover Twelve, the external differences were mainly in the bumpers, horns, fog lamp position and rear lamps. They were also shorter and wider. The engines were entirely new and featured overhead inlet and side exhaust valves (F-head). Cubic capacities were 1595-cc (69·5 x 105 mm) and 2103 cc (65·2 x 105 mm) for the Four and the Six respectively.
1948 Rover P3 Sixty Four-Light
UK

Rover P3 Sixty Four-Light

 

Also see: Rover Car Reviews | The History of Rover (AUS Edition)

 
1948 Rover 60 four-light model, which was powered by a 1595cc four-cylinder engine.
1948 Singer Nine Roadster and Super Ten and Twelve Saloons
UK

Singer Nine Roadster and Super Ten and Twelve Saloons

 

Also see: Singer Car Reviews | The History of Singer

 
The Singer Nine Roadster and Super Ten and Twelve Saloons were continued from 1947, now at £576, £652 and £768 respectively. Posing on the old 'penny-farthing' is actor Dirk Bogarde.
1948 Standard Flying Eight, Twelve and Fourteen
UK

Standard Flying Eight, Twelve and Fourteen

 

Also see: Standard Car Reviews | The History of Standard

 
Standard phased out their old Flying Eight Twelve (shown) and Fourteen models in the summer of 1948, and concentrated on their entirely new Vanguard Saloon.
1948 Standard Vanguard Saloon Series 20S
UK

Standard Vanguard Saloon Series 20S

 

Also see: Standard Car Reviews | The History of Standard

 
Standard decided in 1947 to pursue a one-model policy with their new and very attractive Vanguard Saloon, Series 20S. It was a new car from the ground up and went into full-scale quantity production in 1948. Initially. i.e. until the end of the year, practically all Vanguards were exported. The car had independent front suspension, four-cylinder OHV engine (2088 cc; 85 x 92 mm; 68 bhp at 4000 rpm), three-speed gearbox, with right-hand column shift, 7 ft 10 in wheelbase, 13 ft 10 in overall length, 5 ft 9 in overall width (providing seating for up to six passengers) and 5.50-16 tires. In October an Estate Car variant was introduced, followed by a Van and later a Pick-up truck. Basically the same engine was used in the Ferguson tractor.
1948 Sunbeam-Talbot Ten
UK

Sunbeam-Talbot Ten

 

Also see: Sunbeam Car Reviews | The History of Sunbeam

 
The Sunbeam-Talbot Ten was continued from 1947 in Saloon, Drophead Coupe and Tourer form, until mid-1948 when the entirely new 80 models appeared.
1948 Sunbeam-Talbot 2-Litre
UK

Sunbeam-Talbot 2-liter

 

Also see: Sunbeam Car Reviews | The History of Sunbeam

 
Sunbeam-Talbot 2-liter, which was similar but somewhat larger than the Ten, was also continued from 1947 and superseded in June by the new 90. The Tourer versions were discontinued.
1948 Triumph 1800 Roadster Series 18TR
UK

Triumph 1800 Roadster Series 18TR

 

Also see: Triumph Car Reviews | The History of Triumph

 
Triumph continued their 1800 Saloon, Series 18T and 1800 Roadster, Series 18TR (shown), with virtually no changes until October when the Roadster was fitted with the same 2088-cc engine and three-speed gearbox as the Standard Vanguard. It was redesignated the 2000 Roadster, Series 20TR. The same change was made to the 1800 Saloon in February 1949.
1948 Triumph Roadster 2000
UK

Triumph Roadster 2000

 

Also see: Triumph Car Reviews | The History of Triumph

 
The Triumph 1800 Roadster was redesignated the 2000 Roadster, Series 20TR, when Triumph switced to using the same 2088cc engine as being used in the Standard Vanguard. The same change was made to the 1800 Saloon in February 1949.
1948 Vauxhall Twelve and Fourteen Saloons
UK

Vauxhall Twelve and Fourteen Saloons

 

Also see: Vauxhall Car Reviews

 
Vauxhall Motors kept their 1946-1947 Twelve and Fourteen Saloons in production until July, when they were superseded by the restyled Wyvern and Velox models.
1948 Wolseley Twelve (12/48) Series Ill
UK

Wolseley Twelve (12/48) Series Ill

 

Also see: Wolseley Car Reviews | Wolseley Production Numbers 1940 - 1950

 
The Wolseley Twelve (12/48), Series III, was another example of a basically pre-war car which was in its last production year. In October it was superseded by a new model, the Four-fifty. The Wolseley Eight, Ten, Fourteen (14/60), Eighteen (18/85) and Twenty-five were also phased out during the year.
Latest Classic Car Classifieds


back
Unique Cars and Parts USA - The Ultimate Classic Car Resource
next